StewMac SM2367 Bestellen?

Get a grip on thin files! Stop those skinny files from jumping, wandering, and bending. Gauged Nut Slotting Files are great, but the thin ones can be tough to hold. It’s hard to start a slot without the file chattering or drifting off your line – one small mistake can ruin a new nut. The handy Nut File Backer acts like a spine, stiffening the file for a straighter, more accurate cut. And it’s much easier to hold on to: no more slipping and sliding on a slick nut or saddle.

It’s important to hold your files perfectly horizontal when filing new slots, and this backer makes it easy to tell when your alignment is just right. The file is supported along its entire length – you’ll never need to worry about bending your files.

Simply slide your file into the backer, tighten the 4 hex screws, then file away! Switching out files is a breeze. No special tools needed, any 1/16″ hex key will work. Just loosen the screws, swap the files, tighten, and you’re ready to go.

Features:
– More accurate filing with no slipping
– Better grip with greater control
– Cuts faster
– Prevents thinner files from bending
– Narrow backer holds files up to 0.020″ (0.508mm)
– Wide backer holds files up to 0.056″ (1.142mm)
– Dimensions: 5″ x 1/2″ (127mm x 11mm)

StewMac SM2367 bestellen?

Actieprijs vandaag : 34.75 Euro

Meer informatie >> Naar aanbieder van StewMac SM2367

Naar aanbieder

StewMac SM0864 Bestellen?

This custom-made file gives you a handle on your fret work! It works quickly to level frets or fingerboards, leaving a smooth finish. It’s 1″ (2.5 cm) wide with a comfortable hardwood handle. The 6″ (15 cm) length is useful for general fret levelling use.

This file is a double-cut file for ebony, rosewood and pearl inlays but is also suitable for fretwork. Despite its rough appearance, it leaves a smooth finish. It cuts smoother than most fret leveling files, they work quickly and they’re great for dressing and beveling fret ends.

It works on stainless frets too! Modern stainless-steel fretwire is known to be harder than the traditional nickel-silver blends, but our own shop experience indicates the wire does not cause premature wear of this file.

StewMac SM0864 bestellen?

Actieprijs vandaag : 143.90 Euro

Meer informatie >> Naar aanbieder van StewMac SM0864

Naar aanbieder

Hosco Japan H-TL-NF3A Bestellen?

Set of 3 double-function nut files. Suitable for most acoustic steel-string guitars.

Red file .016″ and .042″ for E and D string
Blue file .026″ and.050″ for B and A string
Yellow file .036″ and .055″ for G and E string

Alternative is to use single files H-NF- for each string gauge or the 10-file set H-NF10 or 11-file set H-NF11.

total length: 190 mm
file length: 100mm

Hosco Japan H-TL-NF3A bestellen?

Actieprijs vandaag : 106.05 Euro

Meer informatie >> Naar aanbieder van Hosco Japan H-TL-NF3A

Naar aanbieder

Hosco Japan H-TL-NF3E Bestellen?

Set of 3 double-function nut files. Suitable for most electric guitars.

Red file .010″ and .026″ for E and D string
Blue file .013″ and .036″ for B and A string
Yellow file .017″ and .046″ for G and E string

Alternative is to use single files H-NF- for each string gauge or the 10-file set H-NF10 or 11-file set H-NF11.

total length: 190 mm
file length: 100mm

Hosco Japan H-TL-NF3E bestellen?

Actieprijs vandaag : 106.05 Euro

Meer informatie >> Naar aanbieder van Hosco Japan H-TL-NF3E

Naar aanbieder

Hosco Japan H-TL-NF3C Bestellen?

Set of 3 double-function nut files. Suitable for most classic guitars.

Red file .030″ and .038″ for E and D string
Blue file .032″ and .042″ for B and A string
Yellow file .035″ and .046″ for G and E string

Alternative is to use single files H-NF- for each string gauge or the 10-file set H-NF10 or 11-file set H-NF11.

total length: 190 mm
file length: 100mm

Hosco Japan H-TL-NF3C bestellen?

Actieprijs vandaag : 106.05 Euro

Meer informatie >> Naar aanbieder van Hosco Japan H-TL-NF3C

Naar aanbieder

Hosco Japan H-TL-NF3B Bestellen?

Set of 3 double-function nut files. Suitable for most bass guitars.

Red file .045″ and .085″
Blue file .065″ and .105″
Yellow file .075″ and .130″

Alternative is to use single files H-NF- for each string gauge or the 10-file set H-NF10 or 11-file set H-NF11.

total length: 190 mm
file length: 100mm

Hosco Japan H-TL-NF3B bestellen?

Actieprijs vandaag : 106.05 Euro

Meer informatie >> Naar aanbieder van Hosco Japan H-TL-NF3B

Naar aanbieder